# Free 100-150 practice questions

> 10 free 100-150 practice questions with the correct answer and an explanation.

Page: https://devopscodelab.com/exams/cisco-100-150/free-practice-questions/
Practice exams: https://devopscodelab.com/exams/cisco-100-150/

### Question 1 of 10

A network monitoring tool shows a 1 Gbps uplink averaging 950 Mbps all day, and users report slow applications. Which conclusion and next step are MOST appropriate?

- A. The link has high jitter, so replace the copper cable with single-mode fiber
- B. The link is near saturation; find the top talkers before adding capacity
- C. The link uses UDP traffic, so convert all applications to use TCP instead
- D. The link has excess bandwidth, so reduce its speed to lower the latency

**Answer:** B

**Explanation:** Sustained use near the link's capacity means congestion, so the sensible next step is to find which hosts or applications consume the most before upgrading. Utilization numbers say nothing about jitter or cable type, lowering speed would worsen congestion, and converting applications to TCP is neither practical nor a fix for saturation.

### Question 2 of 10

A branch office link has 50 ms of latency and plenty of free bandwidth, yet a single large file transfer between two servers never fills the link. Which factor BEST explains the limited throughput for one TCP session?

- A. The UDP checksum forces every datagram to be retransmitted after a timeout
- B. The TCP window size caps how much data is unacknowledged at once
- C. The ARP cache expires during the transfer and stops frames from being sent
- D. The DNS response is cached and slows down the data portion of the transfer

**Answer:** B

**Explanation:** A single TCP session can only send one window of data before waiting for acknowledgments, so on a higher-latency link the window size caps throughput regardless of link capacity. UDP is not used for this transfer, ARP entries are refreshed without halting traffic, and DNS resolution happens only once before the transfer begins.

### Question 3 of 10

A network printer must always keep the same IPv4 address, but the administrator wants to keep managing all addressing from the DHCP server. Which solution meets both goals?

- A. Create a DHCP reservation tied to the printer's MAC address
- B. Assign the printer an APIPA address from the 169.254.0.0 range
- C. Configure a static address on the printer from inside the DHCP scope
- D. Shorten the DHCP lease time so the printer renews more often

**Answer:** A

**Explanation:** A DHCP reservation always hands the same address to a specific MAC address while keeping the configuration centralized on the server. A static address inside the scope can be handed to another client and causes a conflict, a shorter lease does not guarantee the same address, and APIPA addresses are not managed and cannot reach other subnets.

### Question 4 of 10

A technician sees that a laptop's Wi-Fi adapter has the address 169.254.201.7 while coworkers on the same SSID have 10.20.5.x addresses. Which action should the technician try FIRST?

- A. Add a manual route to the 10.20.5.0 network
- B. Flush the laptop's DNS resolver cache
- C. Release and renew the adapter's DHCP lease
- D. Change the adapter to a static 169.254.0.1 gateway

**Answer:** C

**Explanation:** A 169.254.x.x address means the laptop failed to get a DHCP lease, so releasing and renewing (for example, ipconfig /release and /renew) is the first fix to try. A gateway in the link-local range would not provide internet access, a manual route does not fix the missing lease, and the DNS cache has nothing to do with address assignment.

### Question 5 of 10

An employee's Windows laptop shows a strong Wi-Fi signal, but its connection status says "No internet" and ipconfig shows a valid 10.10.4.22 address with gateway 10.10.4.1. Which next step BEST narrows down the problem?

- A. Rename the laptop and reconnect it to the wireless network
- B. Move the laptop closer to the access point and test again
- C. Replace the laptop's wireless adapter with a USB adapter
- D. Ping the gateway, then a public IP, then a public hostname

**Answer:** D

**Explanation:** The laptop has a good signal and a valid address, so testing step by step from the gateway to a public IP and then a hostname shows whether the problem is local routing, internet access, or DNS. A new adapter or moving closer addresses radio issues that are not present, and renaming the computer does not affect connectivity.

### Question 6 of 10

A smart thermostat, door sensors, and lighting controllers are being added to an office network. What do these devices have in common as endpoints?

- A. They are servers that must run a full operating system and host network services
- B. They are IoT devices, often with limited processing power and security
- C. They are network infrastructure devices that forward traffic between VLANs
- D. They are thin clients that depend on a remote desktop server to operate

**Answer:** B

**Explanation:** Thermostats, sensors, and lighting controllers are IoT endpoints, which usually have limited resources and basic security, so they are often isolated on their own network. They do not host services like servers, forward traffic like switches or routers, or run remote desktop sessions like thin clients.

### Question 7 of 10

A technician must set the password that protects privileged EXEC mode on a Cisco router and wants it stored as a hash in the configuration. Which command should be used?

- A. service password-encryption only
- B. enable secret
- C. enable password
- D. username admin password

**Answer:** B

**Explanation:** enable secret sets the privileged EXEC password and stores it as a hash. enable password stores it in plain text, service password-encryption alone applies only weak reversible encryption to existing clear-text passwords, and username ... password creates a local user account rather than the enable password.

### Question 8 of 10

A technician reviews show interfaces status on a Catalyst switch and sees port Gi1/0/12 listed as err-disabled. What does this status mean?

- A. The switch shut the port itself after detecting a violation or error
- B. The port was placed into a VLAN that has not been created yet
- C. The port is operating normally but has no device plugged into it
- D. The port is a trunk and is waiting for the other side to negotiate

**Answer:** A

**Explanation:** Err-disabled means the switch shut the port down because of a detected condition such as a port-security violation or a BPDU guard event, and it stays down until recovered. A port with no device shows notconnect, a missing VLAN shows inactive, and a trunk negotiation issue does not produce err-disabled.

### Question 9 of 10

Users report a web application stopped working right after a scheduled change window last night. What should the technician check FIRST?

- A. The physical cabling for every user who reported the problem
- B. The change records for what was modified in that window
- C. The Wi-Fi channel plan, for interference from nearby networks
- D. The DHCP scope, to see whether all of its addresses are leased

**Answer:** B

**Explanation:** A problem that starts right after a change window most likely relates to that change, so reviewing change records is the fastest path to the cause. Cabling, DHCP exhaustion, and Wi-Fi interference are unlikely to appear suddenly for one application at the same moment as a planned change.

### Question 10 of 10

Hundreds of compromised devices around the world send traffic at the same time to overwhelm an online store. How does this differ from a simple DoS attack?

- A. It is a DoS from a single source that a basic firewall rule can easily stop
- B. It is an on-path attack that reads the store's traffic instead of flooding it
- C. It is a DDoS from many distributed sources, so it is harder to block
- D. It is a phishing campaign that targets the store's customers by email

**Answer:** C

**Explanation:** A distributed denial-of-service uses many sources, often a botnet, so blocking one address does not stop it. A single-source DoS is easier to filter, an on-path attack intercepts traffic rather than flooding it, and phishing targets people rather than overwhelming a service.

Ready for a timed run? Take the free 15-question 100-150 mini exam: https://devopscodelab.com/app/exams/cisco-100-150/mini/

DevOpsCode Lab is not affiliated with Cisco. 100-150 and related names are trademarks of their owners. We write every question ourselves; these are not real exam questions.
