SOT-001

Free SOT-001 practice questions

10 questions from our SOT-001 practice tests, each with the correct answer and a written explanation. Read them with the answers shown, or switch to quiz mode and answer first.

Back to the SOT-001 practice exams

Question 1 of 10, OT Systems and Safety Foundations

A system integrator must connect controllers from several vendors to a plant-wide information platform. The requirements include platform independence, a rich information model, and built-in options for message signing, encryption and certificate-based application authentication. Which protocol BEST meets these requirements?

  1. AOPC UA (IEC 62541) Correct answer
  2. BDNP3 over serial
  3. CModbus TCP
  4. DEtherNet/IP with CIP

Answer and explanation: OPC UA is a platform-independent standard with an extensible information model and a security model that supports signing, encryption and X.509 application certificates. Modbus TCP lacks native security and a rich information model. EtherNet/IP is widely used but its security extension (CIP Security) is not the vendor-neutral information-modeling platform described, and DNP3 over serial is a utility telemetry protocol that does not provide the requested information model.

Question 2 of 10, OT Risk Management

A plant's process hazard analysis (PHA) identified that overpressure in a vessel could cause a release. The OT security team wants to include cyber-initiated causes, such as manipulated setpoints or disabled alarms, in the same structured study. Which approach does this describe?

  1. ARunning a quantitative penetration test against the vessel's pressure transmitter in production
  2. BReplacing the PHA with an annualized loss expectancy calculation for each process vessel
  3. CExtending HAZOP or PHA methods into a cyber PHA that treats cyberattacks as initiating causes Correct answer
  4. DCreating a separate IT risk register that excludes physical consequences from cyber events

Answer and explanation: A cyber PHA, sometimes called a cyber HAZOP, extends established process safety methods so cyber-initiated deviations are analyzed alongside other causes, linking cyber risk to physical consequences. ALE calculations do not analyze process deviations, penetration testing production instruments risks the process, and an IT-only register that excludes physical consequences misses the very impacts the team wants to study.

Question 3 of 10, OT Risk Management

A critical infrastructure operator wants to start its risk work by identifying the few functions whose failure would be catastrophic, assume a capable adversary already has access, and then engineer out the paths that lead to those consequences. Which methodology is this?

  1. AConsequence-driven, cyber-informed engineering Correct answer
  2. BVulnerability-centric patch prioritization
  3. CQualitative likelihood heat mapping
  4. DAnnual compliance gap assessment

Answer and explanation: Consequence-driven, cyber-informed engineering (CCE), developed at Idaho National Laboratory, starts from high-consequence events, assumes compromise and uses engineering changes to remove or limit pathways. A compliance gap assessment measures conformance, vulnerability-centric patching starts from weaknesses rather than consequences, and heat mapping ranks risks without engineering consequence elimination.

Question 4 of 10, OT Threat Intelligence. Choose 2.

A US water utility wants to both receive and contribute threat information with peers and government. Which two channels are designed for this? (Choose two.)

  1. ASubscribing to a vendor's product newsletter
  2. BFiling a regulatory compliance self-report
  3. CJoining the sector's ISAC, such as WaterISAC Correct answer
  4. DPosting details on a public industry forum
  5. EParticipating in CISA's Automated Indicator Sharing Correct answer

Answer and explanation: Sector ISACs and CISA's Automated Indicator Sharing program provide trusted, two-way channels to exchange threat information. A vendor newsletter only delivers product news one way, a compliance self-report addresses regulatory violations rather than threat sharing, and a public forum lacks trust and handling controls and may expose sensitive details.

Question 5 of 10, OT Cybersecurity Architecture, Design, and Engineering

A utility wants access to substation relay settings to be granted only when the user is a protection engineer, the request comes from a utility-managed laptop, and the time falls within an approved maintenance window. Which access control model BEST supports these combined conditions?

  1. AAttribute-based access control Correct answer
  2. BRule-based access control by IP
  3. CDiscretionary access control
  4. DRole-based access control

Answer and explanation: Attribute-based access control evaluates multiple attributes of the user, device and environment, such as job function, device management state and time window, in a single policy decision. RBAC alone considers only role, DAC relies on owner-granted permissions, and IP-based rules cannot express user role or device posture.

Question 6 of 10, OT Cybersecurity Architecture, Design, and Engineering

A protection engineer argues that encrypting GOOSE messages between relays would add latency the protection scheme cannot tolerate. The security architect still wants to prevent spoofed messages. Which approach BEST balances these needs?

  1. AUse message authentication to ensure integrity and origin without full encryption Correct answer
  2. BRoute GOOSE messages through the enterprise firewall for inspection
  3. CAccept spoofing risk because time-critical traffic cannot be protected in any way
  4. DEncrypt all GOOSE traffic regardless of the latency impact on protection

Answer and explanation: Authentication with message authentication codes protects integrity and origin with lower overhead than full encryption, addressing spoofing while respecting timing constraints, as in IEC 62351 approaches. Forcing encryption ignores protection timing, accepting the risk ignores available controls, and routing through an enterprise firewall adds latency and breaks substation design.

Question 7 of 10, OT Security Operations

An OT SOC has limited storage. It wants to support investigations of activity that may have started months earlier. Which retention strategy BEST balances cost and investigative value?

  1. AKeep full captures briefly and flow and protocol metadata much longer Correct answer
  2. BKeep only firewall deny logs because allowed traffic is assumed to be legitimate
  3. CKeep no network data and rely only on operator shift logs for investigations
  4. DKeep full packet captures for a year and discard all metadata after one week

Answer and explanation: Full packet capture is storage-intensive, so a short window combined with long retention of flow and protocol metadata supports investigations of long dwell times at reasonable cost. A year of full PCAP without metadata is costly and less searchable, deny-only logs miss activity that was allowed, and shift logs are not a substitute for network evidence.

Question 8 of 10, OT Security Operations

A new vulnerability with a CVSS base score of 9.8 affects an HMI web service. The HMI is in an isolated zone with no web service exposed and no known exploitation. A medium-severity vulnerability on an internet-reachable remote access gateway is listed in CISA's Known Exploited Vulnerabilities catalog. Which should be prioritized first?

  1. ABoth equally, because severity scores already include asset exposure
  2. BThe HMI, because its CVSS base score is the highest of the two findings
  3. CThe remote access gateway, because it is exposed and actively exploited Correct answer
  4. DNeither, because OT systems should never be patched outside outages

Answer and explanation: Prioritization should weigh exposure and exploitability, and an internet-facing gateway with known exploitation poses a more immediate risk than an unreachable service with a higher base score. CVSS base scores do not account for an organization's specific exposure, and OT systems still need risk-based remediation, sometimes with compensating controls.

Question 9 of 10, OT Incident Management. Choose 2.

After an incident, a manufacturer prepares its lessons-learned output. Which two items should be included? (Choose two.)

  1. ARaw packet captures from the entire incident period
  2. BAssigned owners and deadlines for corrective actions Correct answer
  3. CA recommendation to cancel the IR retainer to save cost
  4. DUpdates to playbooks based on what did and did not work Correct answer
  5. EIndividual performance ratings for each responder

Answer and explanation: Effective lessons learned update procedures and assign corrective actions with owners and deadlines. Raw packet captures belong in the evidence repository rather than the lessons-learned output, performance ratings turn the review into blame and discourage reporting, and cancelling the retainer reduces future readiness.

Question 10 of 10, OT Incident Management

A regional utility adopts a framework that applies the Incident Command System, with an incident commander, defined sections and span-of-control rules, specifically to industrial cyber incidents. Which framework is this?

  1. AMITRE ATT&CK for ICS
  2. BISO/IEC 27035
  3. CNIST CSF 2.0
  4. DICS4ICS Correct answer

Answer and explanation: ICS4ICS adapts the Incident Command System used by emergency responders to industrial control system cyber incidents. NIST CSF 2.0 is a cybersecurity outcomes framework, ISO/IEC 27035 is a general incident management standard, and ATT&CK for ICS catalogs adversary techniques.