NSE7_FSN_AR-7.6

Free NSE7_FSN_AR-7.6 practice questions

10 questions from our NSE7_FSN_AR-7.6 practice tests, each with the correct answer and a written explanation. Read them with the answers shown, or switch to quiz mode and answer first.

Back to the NSE7_FSN_AR-7.6 practice exams

Question 1 of 10, System Configuration and SD-WAN Setup

A hub must evaluate the health of spoke overlays without sending its own probes, using the measurements the spokes already take toward the hub. Which configuration combination achieves this?

  1. ASpokes use detect-mode passive, and the hub enables passive-wan-health-measurement on its firewall policies
  2. BSpokes enable embed-measured-health, and the hub health check uses detect-mode remote Correct answer
  3. CSpokes enable update-cascade-interface, and the hub sets failtime 1 on a health check for each tunnel
  4. DThe hub uses detect-mode prefer-passive, and spokes send TWAMP probes to the hub loopback address

Answer and explanation: With embed-measured-health, spokes put their measured latency, jitter and loss into the probe packets, and a hub health check in remote detect mode uses those values instead of probing. Passive detection measures real traffic on the device that runs it and does not share results with the hub. prefer-passive still relies on local traffic or local probes. update-cascade-interface only brings down a dependent interface and does not share measurements.

Question 2 of 10, System Configuration and SD-WAN Setup

A performance SLA probes 8.8.8.8 with ping every 500 ms, failtime 5 and recoverytime 5. The ISP on port1 starts dropping all probes. Approximately how long does FortiGate take to declare port1 dead, and what happens to static routes through port1 if update-static-route is left at its default?

  1. AAbout 5 seconds; routes are kept but their priority is raised so the other member is preferred
  2. BAbout 2.5 seconds; port1 routes are removed from the routing table until the member recovers Correct answer
  3. CAbout 25 seconds; routes are removed only after the recoverytime counter has also expired
  4. DAbout 2.5 seconds; port1 routes stay installed and only SD-WAN rules stop selecting the member

Answer and explanation: The link is declared dead after failtime consecutive lost probes, so five probes at 500 ms is roughly 2.5 seconds. update-static-route is enabled by default, which removes static routes through a dead member so traffic moves to the remaining members. Keeping the routes installed would only happen with update-static-route disabled, priority is not changed by the health check, and recoverytime applies only to bringing a member back alive.

Question 3 of 10, Central Management

A FortiManager administrator changes an SD-WAN template and must confirm exactly which CLI commands will be pushed to a branch before installing. Which action provides this?

  1. AImport the device policy package again so that differences are shown as conflicts
  2. BRun a policy package consistency check, which lists the CLI commands for each device
  3. CRun the install wizard and use install preview to view the commands for the device Correct answer
  4. DRetrieve the device configuration and compare it with the latest revision history entry

Answer and explanation: Install preview generates the CLI commands that FortiManager will send to the device, which is exactly what the administrator needs before installing. Retrieving the configuration shows the current device state and not the pending changes. Consistency checks look for policy problems rather than generating CLI. Re-importing would overwrite the managed package and is not a preview.

Question 4 of 10, Central Management

An administrator manages 300 FortiGate spokes from FortiManager. Each spoke has a unique loopback address that must be used in shared SD-WAN and BGP templates. Which FortiManager feature should be used to supply the per-device value?

  1. AA separate policy package per spoke containing the loopback address
  2. BMetadata variables referenced in the templates and defined per device Correct answer
  3. CDynamic address objects with a default value but no per-device mapping
  4. DA device group per spoke so the template can be cloned for each group

Answer and explanation: Metadata variables let one template reference a variable such as a loopback address while each device stores its own value. Separate policy packages per spoke do not configure device-level loopbacks and defeat the purpose of templates. A dynamic address without per-device mappings gives every device the same value. Cloning templates per group scales poorly and is not necessary.

Question 5 of 10, Security Profiles

A hub inspects all traffic backhauled from 400 spokes and CPU usage is high. Most traffic is between trusted internal segments. Which approach reduces load while keeping inspection where it adds value?

  1. AApply application control to all policies so that IPS no longer needs to inspect traffic
  2. BRemove IPS from trusted internal-to-internal policies and keep it on internet-bound policies Correct answer
  3. CDisable hardware offloading on the hub so that IPS is processed by the main CPU directly
  4. DChange every policy to proxy-based inspection so that sessions are processed in larger blocks

Answer and explanation: Limiting IPS to policies where threats are expected reduces CPU load while keeping protection on internet-bound traffic. Proxy-based inspection is generally more resource-intensive than flow-based inspection. Disabling hardware offloading increases CPU usage. Application control also uses the IPS engine and does not remove inspection load.

Question 6 of 10, Rules and Routing

A spoke must send a default route to one specific downstream BGP neighbor without advertising it to any other neighbor. Which setting provides this?

  1. Anetwork 0.0.0.0/0 with network-import-check off
  2. Bibgp-multipath enabled on the spoke BGP process
  3. Credistribute static with no route map applied
  4. Dcapability-default-originate on the neighbor Correct answer

Answer and explanation: Default origination is configured per neighbor, so only that neighbor receives the default route, and it can optionally be conditioned with a route map. A network statement with the import check disabled would advertise the default route to every neighbor even without a valid route. Redistributing static routes advertises more than the default to all neighbors. ibgp-multipath affects path installation, not advertisement.

Question 7 of 10, Rules and Routing

In an ADVPN network with two overlays per spoke, a spoke learns another spoke's LAN through the hub route reflector but sees only one path, so shortcuts form over only one overlay. Which BGP change allows the spoke to learn both paths?

  1. AConfigure the spokes as route reflectors as well so they exchange paths directly over both overlays
  2. BRaise the maximum-paths value on the hub so that it reflects every path to all route reflector clients
  3. CEnable additional-path send on the hub and receive on the spokes, with adv-additional-path set to 2 Correct answer
  4. DEnable ibgp-multipath on the spokes so that the single reflected path is installed twice in the FIB

Answer and explanation: Without additional paths, a route reflector advertises only its best path, so BGP additional-path support on hub and spokes lets the reflector send multiple paths for the same prefix. ibgp-multipath installs multiple paths that are already learned but cannot create missing ones. Increasing multipath on the hub does not change how many paths it advertises. Making spokes route reflectors breaks the hub-and-spoke design.

Question 8 of 10, Rules and Routing

Which command shows, for each SD-WAN rule, the members that are currently selected and their order of preference?

  1. Aget router info routing-table all
  2. Bdiagnose firewall proute list
  3. Cdiagnose sys sdwan health-check
  4. Ddiagnose sys sdwan service Correct answer

Answer and explanation: diagnose sys sdwan service lists every rule with its members, their status and selection order. The health-check command displays SLA measurements rather than rule decisions. The routing table shows routes but not SD-WAN rule selection. diagnose firewall proute list shows policy routes and rule matching criteria, but the service command is the one designed to show the current member preference per rule.

Question 9 of 10, Advanced IPsec

A hub dial-up phase 1 has net-device disabled and is used by many spokes with overlapping phase 2 selectors of 0.0.0.0/0. Spoke LAN routes are learned through BGP. Which phase 1 setting should the administrator disable to stop the hub from also installing IKE-derived static routes for each spoke's selectors?

  1. Amode-cfg
  2. Badd-route Correct answer
  3. Cexchange-interface-ip
  4. Dauto-discovery-sender

Answer and explanation: add-route installs routes based on the negotiated phase 2 selectors of dial-up peers, which is redundant and can conflict when BGP already provides spoke routes. mode-cfg assigns addresses to clients and does not control selector routes. auto-discovery-sender enables ADVPN shortcut offers. exchange-interface-ip shares tunnel interface addresses between peers and does not create selector routes.

Question 10 of 10, Advanced IPsec

A branch has a lossy LTE overlay used for voice. The administrator wants the tunnel to send redundant packets so that receivers can rebuild lost packets, but only when the health check shows loss. Which feature should be configured?

  1. ASD-WAN packet duplication in force mode across both overlay members
  2. BIPsec anti-replay set to loose so that late packets are not discarded
  3. CAn egress shaping profile that guarantees bandwidth for the voice class
  4. DIPsec forward error correction driven by the SD-WAN health check Correct answer

Answer and explanation: IPsec forward error correction adds parity packets so the receiver can rebuild lost packets, and it can be made adaptive based on health-check measurements. Packet duplication in force mode copies every packet over another member regardless of loss. Loose anti-replay accepts out-of-order packets but cannot recover lost ones. Shaping guarantees bandwidth but does not compensate for loss.