200-301 study guide: CCNA exam domains, plan and common mistakes
Written and reviewed by the DevOpsCode Lab Team. Last updated 19 November 2026.
200-301 is the exam for the Cisco Certified Network Associate (CCNA). It checks that you can build and run a small enterprise network on Cisco gear: addressing, switching and VLANs, routing with static routes and OSPF, core IP services, security basics, wireless and an introduction to network automation.
What the exam tests
CCNA questions are technical and often show configuration output. You may get a show ip route
table and be asked which path a packet takes, a show interfaces trunk output with a fault to
find, or a topology where you choose the right ACL or NAT statement. You need to know IOS commands
well enough to read their output, not just recognize their names, and you need to subnet quickly
for both IPv4 and IPv6.
Domains and how much each counts
| Domain | Weight | What to be able to do | Questions in our bank |
|---|---|---|---|
| Network Fundamentals | 20% | Network components and topologies, cabling, TCP and UDP, IPv4 and IPv6 subnetting, wireless principles, switching concepts | 58 |
| Network Access | 20% | VLANs and trunks, inter-VLAN connectivity, CDP and LLDP, EtherChannel, Rapid PVST+ spanning tree, wireless architectures and WLC basics | 58 |
| IP Connectivity | 25% | Reading the routing table, how a router picks a route, static and default routes for IPv4 and IPv6, single-area OSPFv2, first hop redundancy | 72 |
| IP Services | 10% | NAT and PAT, NTP, DHCP and DNS, SNMP and Syslog, QoS concepts, SSH, TFTP and FTP | 29 |
| Security Fundamentals | 15% | Security concepts, device access control, passwords and AAA, VPN basics, ACLs, layer 2 security such as DHCP snooping and port security, wireless security | 44 |
| Automation and Programmability | 10% | Controller-based and software-defined networking, REST APIs, JSON, configuration management tools, AI and machine learning in network operations | 30 |
IP Connectivity is the largest domain, and with Network Access it covers almost half of the exam.
Exam format
Our practice tests use 60 questions in 120 minutes with a 75% pass mark. The real CCNA is a 120-minute exam that mixes multiple-choice and drag-and-drop questions with simulations where you configure or troubleshoot devices. Cisco does not let you return to a question after you move on, and it does not publish a fixed passing score. Check the official Cisco exam page for the current format, price and objectives before you book.
Who should take it
- Network technicians who work with Cisco switches and routers.
- Network+ holders who want a vendor certification with deeper configuration skills.
- System and cloud administrators who need solid routing and switching knowledge.
Cisco lists no formal prerequisite. Lab every topic in a simulator such as Packet Tracer.
A 4-week study plan
| Week | Focus | Practice |
|---|---|---|
| 1 | Network Fundamentals: subnetting IPv4 and IPv6, TCP and UDP, cabling, switching concepts | Practice mode on this domain; subnet daily; take one full test at the end of the week as a baseline |
| 2 | Network Access: VLANs, trunks, EtherChannel, spanning tree roles and states, wireless architectures | Domain quiz; build a two-switch VLAN lab with a trunk and verify it with show commands |
| 3 | IP Connectivity: routing table, static routes, OSPF neighbors and DR election, FHRP | Domain quiz; read routing tables in every wrong-answer explanation until the logic is automatic |
| 4 | IP Services, Security and Automation, then full exams: NAT, ACLs, port security, REST and JSON | Two full timed tests, then the mistakes quiz; book the exam when you score 80%+ twice |
Topics people often get wrong
- How a router chooses a route. Longest prefix match comes first. Only between routes to the same prefix does administrative distance decide which source wins, and the metric then compares routes from the same protocol. A /28 static route beats a /24 OSPF route regardless of distance.
- OSPF neighbor problems. Hello and dead timers, area ID, subnet and authentication must match for an adjacency to form. The DR is chosen by highest priority, then highest router ID, and the election does not preempt.
- Spanning tree root. The switch with the lowest bridge ID (priority, then MAC address) becomes root. Root ports point toward the root; designated ports point away from it on each segment.
- ACL placement and wildcards. Put standard ACLs close to the destination and extended ACLs close to the source. A wildcard of 0.0.0.255 matches the first three octets, and every ACL ends with an implicit deny.
- NAT terms. Inside local is the private address of the inside host; inside global is the public address that represents it. PAT maps many inside hosts to one global address by port.
How to use the practice tests
Start with the free 200-301 questions to see the style. Then take one full timed test in exam mode for a baseline and look at the score by domain. Spend most of your time in the two weakest domains with domain quizzes, and finish with the mistakes quiz before each new full test. The readiness number tells you when your recent scores hold above the pass mark across all domains.
Frequently asked questions
How hard is the CCNA? It is an associate exam, but deep. People who configure Cisco devices at work often need 6–8 weeks; newcomers to networking commonly study for several months.
Do I need Network+ first? No. It is not required, but it covers the fundamentals that the CCNA assumes and moves faster through.
How long is the certification valid? Cisco certifications are valid for three years and can be renewed by passing qualifying exams or earning continuing education credits.
Are these the real exam questions? No. Every question is written by us for the published exam topics. We never use leaked or recalled exam content.
DevOpsCode Lab is not affiliated with or endorsed by Cisco. Exam names are trademarks of their owners. Check the official Cisco exam page for the current price, format and objectives before you book.